GSAK - The Swisses Knives Index du Forum
 
S’enregistrer
 
GSAK - The Swisses Knives Index du Forum FAQ Rechercher Membres Groupes Profil Se connecter pour vérifier ses messages privés Connexion
 
published this week

 
Poster un nouveau sujet   Répondre au sujet    GSAK - The Swisses Knives Index du Forum -> Consulate - Consulat -> Consulate S-H - Conulat S-H
Sujet précédent :: Sujet suivant  
Auteur Message
DMT


Hors ligne

Inscrit le: 11 Fév 2018
Messages: 532
Localisation: 合肥

MessagePosté le: Jeu 19 Juil 2018 - 11:40    Sujet du message: published this week Répondre en citant

Concrete Garages | Accommodating Your 4wd Vehicle

Author: Nicolas Paice






Coupled with the increasing popularity of the 4WD leisure vehicle comes a demand for increased size and height of replacement concrete sectional garages.


Typically a prefabricated building is 6ft6in (1.98m) to eaves which provides actual under-door clearances in the region of 6ft1in (1.8m). For example this height is equal to that of a Land Rover Discover and a Classic Range Rover and that’s before your consider the roof rack and aerial!






Most manufacturers of concrete sectional buildings offer an increased eaves and door clearance; some can achieve greater clearance simply by exchanging the main door for vertical-lift ‘shutter’ type operation. There is a common misconception that roof style will affect actual internal clearance http://www.montrealcanadiensteamstore.com/adidas-dickie-moore-jersey , this simply is not true.






We recommend an eaves height no less that 7ft6in (2.29m) as other factors such as the slope towards your garage may reduce your actual clearance as well as a weather-bar situated behind the door. Only a few manufacturers can offer 7ft6in panel height as the technology behind fabricating such a tall panel escapes some brands.






It is worthwhile to note that even at 2.29m to eaves this building is still below one of the planning thresholds which places a restriction at 3.0m to eaves and 4.0m to ridge height.






For further increased height buildings suitable for lorries, minibuses and forklift trucks often available are commercialindustrial buildings. The construction of these buildings is similar to concrete sectional garages since the same panels are utilised to create the lower exterior of the building; Plastisol coated box profile steel sheeting is then used to ‘build-up’ to the required height and also used to roof the building. Often the client can specify this sheeting in one of 10 popular colours to match the local environment, regulations or corporate image.






























Article Source: Link


About the Author:


Background: The author has almost 20yrs retail experience in the concrete garage trade. As well as advising on the most suitable building per application advice is also tendered on groundwork preparation and all aspects of planning and building control. The writer resides in Chesterfield, Derbyshire, UK and operates from one of the regions largest concrete garage showrooms. See their website at www.4concretegarages
"
SAN FRANCISCO, June 10 (Xinhua) -- A team of researchers has for the first time discovered magnetism in the 2-D world of monolayers, or materials that are formed by a single atomic layer.

The findings, published this week in the journal Nature, demonstrate that magnetic properties can exist even in the 2-D realm, opening a world of potential applications, as magnetic materials form the basis of technologies that play increasingly pivotal roles in our lives today.

""What we have discovered here is an isolated 2-D material with intrinsic magnetism, and the magnetism in the system is highly robust,"" said Xiaodong Xu, a professor of physics and of materials science and engineering at the University of Washington (UW). ""We envision that new information technologies may emerge based on these new 2-D magnets.""

Xu and Massachusetts Institute of Technology (MIT) physics professor Pablo Jarillo-Herrero led the international team of researchers who proved that the material, chromium triiodide, or CrI3, has magnetic properties in its monolayer form.

Other groups, including co-author Michael McGuire at the Oak Ridge National Laboratory, which is managed for the United States Department of Energy, had previously shown that CrI3, in its multilayered, 3-D, bulk crystal form, is ferromagnetic. In ferromagnetic materials, the ""spins"" of constituent electrons, analogous to tiny, subatomic magnets, align in the same direction even without an external magnetic field.

However, no 3-D magnetic substance had previously retained its magnetic properties when thinned down to a single atomic sheet.

""You simply cannot accurately predict what the electric, magnetic, physical or chemical properties of a 2-D monolayer crystal will be based on the behavior of its 3-D bulk counterpart,"" co-lead author and UW doctoral student Bevin Huang was quoted as saying in a news release from the university in U.S. Pacific Northwest.

Atoms within monolayer materials are considered ""functionally"" two-dimensional because the electrons can only travel within the atomic sheet, like pieces on a chessboard.

The researchers used a special type of microscopy to detect a signature in CrI3, as in other ferromagnetic materials when a beam of polarized light is reflected off the material's surface, indicative of intrinsic ferromagnetism in an isolated monolayer.

And surprisingly, in CrI3 flakes that are two layers thick, the telltale optical signature disappeared. This indicates that the electron spins are oppositely aligned to one another, a term known as anti-ferromagnetic ordering. Ferromagnetism returned in three-layer CrI3.

Yet to conduct further studies to understand why CrI3 displayed these layer-dependent magnetic phases, Xu noted that ""2-D monolayers alone offer exciting opportunities to study the drastic and precise electrical control of magnetic properties, which has been a challenge to realize using their 3-D bulk crystals.

China calls for solidarity, cooperation as SCO admits new members

Red alert for rainstorm in China's .


Revenir en haut
Publicité






MessagePosté le: Jeu 19 Juil 2018 - 11:40    Sujet du message: Publicité

PublicitéSupprimer les publicités ?
Revenir en haut
Montrer les messages depuis:   
Poster un nouveau sujet   Répondre au sujet    GSAK - The Swisses Knives Index du Forum -> Consulate - Consulat -> Consulate S-H - Conulat S-H Toutes les heures sont au format GMT + 2 Heures
Page 1 sur 1

 
Sauter vers:  

Index | Panneau d’administration | Creer un forum | Forum gratuit d’entraide | Annuaire des forums gratuits | Signaler une violation | Conditions générales d'utilisation